Custom-made lower leg prosthesis — fabrication, customization, comfort, and mobility

Homilka modular prostheses

Current solutions for active and comfortable walking

In case of amputation of the lower back, we produce modular prostheses of a new generation, which ensure high functionality, reliability and comfort for the amputated patient. The skin prosthesis is selected and designed individually, depending on the anatomical characteristics of the patient, level of activity and need for re-suction. The modular prosthesis of the homilla is made up of a coxoprimal sleeve, a pediline insert, a non-supporting module and a foot, and in case of even a short homilla or a pathology of the knee joint, it can be additionally secured with a sleeve on the knee (cuff).
Cucco-primary sleeves for prosthetic limbs can be of different designs: a sleeve with a deep fit and buried waste; benefit from frequent burials of the kneecap; the benefit of deep accumulation of the knee and with an even distribution of distribution over the entire surface of the kuksi.

In case of a short knee or pathologies of the knee joint, the steg cuff can be further twisted for better fixation.

Warehouses of modular prosthesis Gomilka

1. Cooksoprimal sleeve This is the main element of the prosthesis, which ensures the transfer of tension from the cooksie to the prosthesis. It is prepared individually for the patient’s plaster or digital cookie. The sleeve demonstrates proper fixation, stability and comfort.

2. The cushion insert (liner) will provide shock absorption, skin protection and an even distribution of the vice. The type of liner is selected carefully based on the sensitivity of the skin, which will suit any fabric and level of preference.

3. Load-bearing module A metal or carbon structural element that connects the sleeve to the foot. Its design is designed for both static and dynamic aspects.

4. The prosthetic foot is selected according to the patient’s level of activity and needs.

Fixation systems and sleeve types

For reliable fastening of the sleeve, it is most common to use a vacuum system. Vacuum fastening creates additional stability and ensures an even distribution of distribution.

To remove the prosthesis, it is enough to open the valve and remove the primary sleeve from the cup.

Types of coxoprimary sleeves for homilk prostheses

We produce sleeves of different designs, depending on individual indications:

Advantages of our modular homilka's prostheses

• Individual selection and preparation – the design is created specifically for the anatomical characteristics of the patient.
• High landing accuracy – It is possible to reach a wide range of modern modeling technologies.
• Light and soft materials – ensure comfort and durability of the product.
• Comfort during wet bathing – optimal distribution of avantagement without teasing.
• Shvidke regulation and maintenance – the ability to quickly adapt the prosthesis to suit the needs of the doctor.
• Suitable for any level of activity – from a spent daily wage to sports activities.
• Sleeve with deep fit – will ensure a better fit.
• Supraviral grip – vikorystvovaetsya with the anatomical features of kuksi.
• Sleeve with frequent burials of the kneecap – adds stability.
• Sleeve with deep burials of the kneecap – Vanishment evenly distributes.

Team of Fahivts

Our prosthetists-orthosists accompany the patient at all stages — From the first inspection to the beginning and further service.

Mi pragnemo, shcheb kozhen koristuvach otrimav prosthesis, which allows you to turn to an active, independent life.

Prosthetic steg for bathing

Safety, comfort and freedom on the water

Bath prostheses are intended for patients with amputation on the lumbar or lumbar sides. The stinks allow you to safely carry out hygienic procedures, take off your shoes at the water basins, drain the pool and feel like it’s time to stop the whiteness of the water.

Such prostheses are designed with improved elasticity and ease of viewing.

Intended for vicorization in the vologo middle – near the bathtub or in the cold waters. Stinks can be made on the same level and are made from spherical plastic.

Features of such prostheses:

• Technological openings for changing buoyancy.
• Waterproof feet.
• Vacuum or belt fastening.

Materials and construction

The denture is prepared using ball plastic, which does not absorb water, resistant to corrosion and easy to see.

To change buoyancy, technological openings can be installed to allow water to freely pass through the structure.

Foot

The prosthesis is equipped with a hinged foot, which does not accommodate loose elements and is as reliable as possible when in contact with water.

Stop without hinges

Artless feet are indicated for patients with low to moderate activity. They have a wear-resistant, reliable design that ensures elasticity when stepping on footing or rolling.

Stop joints

Focused on patients with low to moderate activity. This is a reliable solution for first-time or summer patients with amputation on the level of the vertex to ensure more natural transition. It is also recommended for use in prosthetic limbs with a locking knee joint.

Carbon (energy saving) feet

Carbon feet are reserved for active patients who have a medium to high level of mobility. After an hour of walking, such feet will provide springiness when stepping on the foot, a dynamic transition during the transfer phase, as well as universal elasticity and compensation for unevenness of the supporting surface. This is achieved through the use of structural elements made of composite materials (carbon and elastomer), which improve hand grip and improve walking dynamics.

Mounting system

Fixation is provided for rakhunok:

• supracondyle grip (SC-system),
• textile padthat wipes the sleeve on the water near the water.

Advantages of bathing prostheses

• Resistant to water ingress and corrosion.
• Simply more securely attached to the watery mind.
• Lightweight, quick and easy to use.
• Possibility of safe transfer in the pool, shower and natural ponds.
• Comfortable rotation to active repair

Preparation before prosthetics

Rehabilitation and preparation begin immediately after amputation. At what stage it is important:

• put away the nabryak;
• carry out compression therapy;
• Know your language and prepare them before you start;
• learn to keep an eye on the kuksa.

How to go through the process of prosthetics?

• Consultation – important design, patient needs and level of mobility.
• Knowing the world – Testing of materials is carried out, and the looseness of suglobs is assessed.
• Preparation of individual sleeve – one of the most important stages.
• Fitting and adjustment – the patient begins to use a prosthesis.
• Final installation – After adaptation, the finished product appears.

Stages of functional abilities

• I stage – transfer in a place with a support.
• II stage – interchange the posture of the premises.
• III stage – neobmezhene peresuvannya be-de.
• IV stage – mobility is active due to high demand.

Prosthetics – This is not less of a change in fragility, but of a return to a full-fledged life. Our team of specialists will provide you with a clear and comfortable prosthesis that will help you regain freedom of movement!